Filter By:
- Show More Brands
- Show Fewer Brands
- Show More Sizes
- Show Fewer Sizes
- Show More Model Years
- Show Fewer Model Years
Other
$24.00 - $49.99
Hellbender bearings have an improved seal structure and are cross compatible with Cane Creek headsets.
$24.00 - $52.99
Hellbender bearings have an improved seal structure and are cross compatible with Cane Creek headsets.
$29.99
40-Series replacement cartridge bearings feature durable black oxide construction.
- Compatible with 110-, 40-, and 10-Series headsets
$39.99
Rebuild kits come with everything you need to service moving parts on a Cane Creek Thudbuster suspension seatpost.
- Rebuild bushing tools
- LT arm screws (M4 x 20mm)
- Saddle clamp bolt (M5 x 35mm)
- Saddle clamp spherical washers
- Saddle clamp adjustment knob
$49.00
Slamset top headsets are designed to keep the stack height low.
- Hellbender bearings with improved seal structure
$79.99
A higher quality spring greatly improves the performance of your coil shock. VALT springs from Cane Creek are much lighter than traditional steel springs while pushing the boundaries of performance and durability.
- Inner diameter of 36.5mm is compatible with all Cane Creek coil shocks
- Also compatible with Manitou, Marzocchi, XFusion, ELKA/MRP, BOS and DSP
- Compatible with Fox coil shocks with required spring clip adaptor
$79.99
A higher quality spring greatly improves the performance of your coil shock. VALT springs from Cane Creek are much lighter than traditional steel springs while pushing the boundaries of performance and durability.
- Inner diameter of 36.5mm is compatible with all Cane Creek coil shocks
- Also compatible with Manitou, Marzocchi, XFusion, ELKA/MRP, BOS and DSP
- Compatible with Fox coil shocks with required spring clip adaptor
$99.99
Cane Creek Progressive Rate VALT coil springs are designed to provide riders with a true rise-in-rate spring curve.
- Springs feature the progressiveness and ramp-up that hard-charging riders demand
- Designed for use with Cane Creek Coil shocks
- Progression begins at 50% into the stroke of the spring
- Crafted from high-performance spring steel
- Inner diameter of 36.5mm is compatible with all Cane Creek coil shocks
$93.00
All CeramicSpeed Bearings are hand-built in Denmark. Super-smooth CeramicSpeed grade 3 Silicone Nitride balls are matched (within microns) with hardened steel raceways that feature an ultra-smooth polished groove.
The balls are held in place by a reinforced polyamide cage. Every bearing is optimized with a low-viscosity CeramicSpeed All Round Grease to minimize friction and increase bearing life. Non-contact seals complete the bearings, keeping dirt and moisture out. CeramicSpeed Bearings can be used for any cycling discipline: Road, TT, Tri, Track, Cross, and MTB. The benefits are super low friction, better power transfer, and increased bearing life.
During the building process, we check each bearing four times by hand to ensure that all parts are matched perfectly. CeramicSpeed Balls are 400% smoother, 128% harder, and 58% lighter than standard steel bearings normally used in the bicycle industry. When comparing the CeramicSpeed Balls with other ceramic balls in the industry, you will find that the CeramicSpeed Balls are 15% harder, take 99% higher loads, and are 100% smoother.
- Inner Diameter: 8mm
- Outer Diameter: 22mm
- Width: 7mm
$110.00
All CeramicSpeed Bearings are hand-built in Denmark. Super-smooth CeramicSpeed grade 3 Silicone Nitride balls are matched (within microns) with hardened steel raceways that feature an ultra-smooth polished groove.
The balls are held in place by a reinforced polyamide cage. Every bearing is optimized with a low-viscosity CeramicSpeed All Round Grease to minimize friction and increase bearing life. Non-contact seals complete the bearings, keeping dirt and moisture out. CeramicSpeed Bearings can be used for any cycling discipline: Road, TT, Tri, Track, Cross, and MTB. The benefits are super low friction, better power transfer, and increased bearing life.
During the building process, we check each bearing four times by hand to ensure that all parts are matched perfectly. CeramicSpeed Balls are 400% smoother, 128% harder, and 58% lighter than standard steel bearings normally used in the bicycle industry. When comparing the CeramicSpeed Balls with other ceramic balls in the industry, you will find that the CeramicSpeed Balls are 15% harder, take 99% higher loads, and are 100% smoother.
- Inner Diameter: 15mm
- Outer Diameter: 21mm
- Width: 4mm
$110.00
All CeramicSpeed Bearings are hand-built in Denmark. Super-smooth CeramicSpeed grade 3 Silicone Nitride balls are matched (within microns) with hardened steel raceways that feature an ultra-smooth polished groove.
The balls are held in place by a reinforced polyamide cage. Every bearing is optimized with a low-viscosity CeramicSpeed All Round Grease to minimize friction and increase bearing life. Non-contact seals complete the bearings, keeping dirt and moisture out. CeramicSpeed Bearings can be used for any cycling discipline: Road, TT, Tri, Track, Cross, and MTB. The benefits are super low friction, better power transfer, and increased bearing life.
During the building process, we check each bearing four times by hand to ensure that all parts are matched perfectly. CeramicSpeed Balls are 400% smoother, 128% harder, and 58% lighter than standard steel bearings normally used in the bicycle industry. When comparing the CeramicSpeed Balls with other ceramic balls in the industry, you will find that the CeramicSpeed Balls are 15% harder, take 99% higher loads, and are 100% smoother.
- Inner Diameter: 15mm
- Outer Diameter: 24mm
- Width: 5mm
$110.00
All CeramicSpeed Bearings are hand-built in Denmark. Super-smooth CeramicSpeed grade 3 Silicone Nitride balls are matched (within microns) with hardened steel raceways that feature an ultra-smooth polished groove.
The balls are held in place by a reinforced polyamide cage. Every bearing is optimized with a low-viscosity CeramicSpeed All Round Grease to minimize friction and increase bearing life. Non-contact seals complete the bearings, keeping dirt and moisture out. CeramicSpeed Bearings can be used for any cycling discipline: Road, TT, Tri, Track, Cross, and MTB. The benefits are super low friction, better power transfer, and increased bearing life.
During the building process, we check each bearing four times by hand to ensure that all parts are matched perfectly. CeramicSpeed Balls are 400% smoother, 128% harder, and 58% lighter than standard steel bearings normally used in the bicycle industry. When comparing the CeramicSpeed Balls with other ceramic balls in the industry, you will find that the CeramicSpeed Balls are 15% harder, take 99% higher loads, and are 100% smoother.
- Inner Diameter: 15mm
- Outer Diameter: 28mm
- Width: 7mm
$120.00
All CeramicSpeed Bearings are hand-built in Denmark. Super smooth CeramicSpeed grade 3 Silicone Nitride balls are matched (within microns) with hardened steel raceways that feature an ultra-smooth polished groove.
The balls are held in place by a reinforced polyamide cage. Every bearing is optimized with a low-viscosity CeramicSpeed All Round Grease to minimize friction and increase bearing life. Non-contact seals complete the bearings, keeping dirt and moisture out. CeramicSpeed Bearings can be used for any cycling discipline: Road, TT, Tri, Track, Cross, and MTB. The benefits are super low friction, better power transfer, and increased bearing life.
During the building process, we check each bearing four times by hand to ensure that all parts are matched perfectly. CeramicSpeed Balls are 400% smoother, 128% harder, and 58% lighter than standard steel bearings normally used in the bicycle industry. When comparing the CeramicSpeed Balls with other ceramic balls in the industry, you will find that the CeramicSpeed Balls are 15% harder, take 99% higher loads, and are 100% smoother.
- Inner Diameter: 17mm
- Outer Diameter: 28mm
- Width: 7mm
$140.00
All CeramicSpeed Bearings are hand-built in Denmark. Super-smooth CeramicSpeed grade 3 Silicone Nitride balls are matched (within microns) with hardened steel raceways that feature an ultra-smooth polished groove.
The balls are held in place by a reinforced polyamide cage. Every bearing is optimized with a low-viscosity CeramicSpeed All Round Grease to minimize friction and increase bearing life. Non-contact seals complete the bearings, keeping dirt and moisture out. CeramicSpeed Bearings can be used for any cycling discipline: Road, TT, Tri, Track, Cross, and MTB. The benefits are super low friction, better power transfer, and increased bearing life.
During the building process, we check each bearing four times by hand to ensure that all parts are matched perfectly. CeramicSpeed Balls are 400% smoother, 128% harder, and 58% lighter than standard steel bearings normally used in the bicycle industry. When comparing the CeramicSpeed Balls with other ceramic balls in the industry, you will find that the CeramicSpeed Balls are 15% harder, take 99% higher loads, and are 100% smoother.
- Inner Diameter: 20mm
- Outer Diameter: 32mm
- Width: 7mm
$169.00
All CeramicSpeed Bearings are hand-built in Denmark. Super-smooth CeramicSpeed grade 3 Silicone Nitride balls are matched (within microns) with hardened steel raceways that feature an ultra-smooth polished groove.
The balls are held in place by a reinforced polyamide cage. Every bearing is optimized with a low-viscosity CeramicSpeed All Round Grease to minimize friction and increase bearing life. Non-contact seals complete the bearings, keeping dirt and moisture out. CeramicSpeed Bearings can be used for any cycling discipline: Road, TT, Tri, Track, Cross, and MTB. The benefits are super low friction, better power transfer, and increased bearing life.
During the building process, we check each bearing four times by hand to ensure that all parts are matched perfectly. CeramicSpeed Balls are 400% smoother, 128% harder, and 58% lighter than standard steel bearings normally used in the bicycle industry. When comparing the CeramicSpeed Balls with other ceramic balls in the industry, you will find that the CeramicSpeed Balls are 15% harder, take 99% higher loads, and are 100% smoother.
- Inner Diameter: 17mm
- Outer Diameter: 26mm
- Width: 5mm
$179.00
All CeramicSpeed Bearings are hand-built in Denmark. Super-smooth CeramicSpeed grade 3 Silicone Nitride balls are matched (within microns) with hardened steel raceways that feature an ultra-smooth polished groove.
The balls are held in place by a reinforced polyamide cage. Every bearing is optimized with a low-viscosity CeramicSpeed All Round Grease to minimize friction and increase bearing life. Non-contact seals complete the bearings, keeping dirt and moisture out. CeramicSpeed Bearings can be used for any cycling discipline: Road, TT, Tri, Track, Cross, and MTB. The benefits are super low friction, better power transfer, and increased bearing life.
During the building process, we check each bearing four times by hand to ensure that all parts are matched perfectly. CeramicSpeed Balls are 400% smoother, 128% harder, and 58% lighter than standard steel bearings normally used in the bicycle industry. When comparing the CeramicSpeed Balls with other ceramic balls in the industry, you will find that the CeramicSpeed Balls are 15% harder, take 99% higher loads, and are 100% smoother.
- Inner Diameter: 17mm
- Outer Diameter: 30mm
- Width: 7mm
$180.00
All CeramicSpeed Bearings are hand-built in Denmark. Super-smooth CeramicSpeed grade 3 Silicone Nitride balls are matched (within microns) with hardened steel raceways that feature an ultra-smooth polished groove.
The balls are held in place by a reinforced polyamide cage. Every bearing is optimized with a low-viscosity CeramicSpeed All Round Grease to minimize friction and increase bearing life. Non-contact seals complete the bearings, keeping dirt and moisture out. CeramicSpeed Bearings can be used for any cycling discipline: Road, TT, Tri, Track, Cross, and MTB. The benefits are super low friction, better power transfer, and increased bearing life.
During the building process, we check each bearing four times by hand to ensure that all parts are matched perfectly. CeramicSpeed Balls are 400% smoother, 128% harder, and 58% lighter than standard steel bearings normally used in the bicycle industry. When comparing the CeramicSpeed Balls with other ceramic balls in the industry, you will find that the CeramicSpeed Balls are 15% harder, take 99% higher loads, and are 100% smoother.
- Inner Diameter: 30mm
- Outer Diameter: 42mm
- Width: 7mm
$269.00
Improve the performance of your 11-speed Shimano rear derailleur with pulleys that reduce friction and increase bearing life. Ours are designed to work with less drag, adding to the power transmitted to the rear wheel.
- Uses low-drag, long-life Standard Bearing with hardened-steel races and our super-round CeramicSpeed balls.
- A set consists of differing upper and lower pulleys: they are marked as such and have directional arrows etched on them so you know exactly how to install them.
- These pulleys are compatible with all Shimano 11-speed rear derailleurs except XT or XTR.
- The kits come with CeramicSpeed oil in a 15ml dropper bottle. The bearings come pre-oiled.
In the box:
- 2 x 11-tooth pulley wheels
- 4 x spacers
- CeramicSpeed Bearing Oil in 15 ml dropper bottle
- Sticker sheet
$339.00
Replacement Pulley Wheels for the CeramicSpeed OSPW System. Includes 2 pulley wheels.
- Precision-machined aluminum pulleys
- For use with CeramicSpeed's Oversized Pulley Wheel System only
- Coated races increase bearing service life by increasing hardness of race and reducing corrosion
- CeramicSpeed products with coated bearings include a 6-year warranty
$379.00
SRAM's 1x Eagle component system boasts a twelve-speed cassette. We built pulleys that can handle the load better than stock. These CeramicSpeed Pulley Wheels work with less drag, adding to the power transmitted to the rear wheel while offering greater durability, going longer between replacement intervals.
These pulleys are also fully compatible with the SRAM Eagle AXS derailleur.
The aluminum pulleys with standard bearings are 34.4% more efficient than stock and use our low-drag, long-life Standard Bearing with hardened-steel races and our super-round CeramicSpeed balls. The upper and lower pulleys both have a narrow-wide tooth design with 14 teeth each. As the upper and lower pulleys have different tasks, they have different shapes. You'll find they are thus marked, and have directional arrows.
These pulleys should be installed with stock SRAM pulley spacers. Save those from your old pulleys before installing CeramicSpeed.
The kits come with CeramicSpeed Oil in a 15ml dropper bottle and grease in 5ml syringe. The bearings come pre-oiled. The grease can be used on the pulley bearings when riding in particularly harsh environments.
In the box:
- 2 x 14-tooth pulley wheels
- CeramicSpeed Bearing Oil in 15ml dropper bottle
- CeramicSpeed Grease in 5ml syringe
- Sticker sheet
$499.00 - $629.00
This is an updated version of the Oversized Pulley Wheel System for Shimano 9100/9150 and 8000 SS/8050 SS. This new design has an integrated stop tower for easier mounting.
The CeramicSpeed Oversized Pulley Wheels System has been proven to be the fastest pulley system in the world, providing energy savings starting at 2.4 watts compared to standard Shimano systems.
The OSPW System for Shimano 9100/9150 and 8000 SS/8050 SS is an industry-leading product, chosen by many of the world's leading cycling teams and professional triathletes.
It features a 13-tooth upper pulley wheel and a 19-tooth lower to provide absolute optimization of the rear derailleur, and these oversized aluminum pulley wheels come fitted with either standard or coated CeramicSpeed Bearings: your choice.
The Shimano 9100/8000 OSPW system is compatible up to a 32 tooth cassette for both Dura Ace & Ultegra derailleurs
The typical overall power savings of the OSPW System for Shimano 9100/9150/8000 is 30%-60% over a stock setup.
The oversized pulley wheels have lifespan that is 3-5 times longer than the commonly used standard pulleys on the market.
Please note: The OSPW System for 9100/9150 and 8000 SS/8050 SS is NOT compatible with Ultegra 8000-GS or 8050-GS (medium cage) derailleurs, nor with the clutch-equipped Ultegra RD RX800 & RX805. Choose CeramicSpeed's OSPW X for Shimano RX800/805 for a compatible RX800 & RX805 version. For a compatible upgrade for Ultegra 8000-GS or 8050-GS choose their Pulley Wheels for Shimano, 11s NW.
In The Box:
- A complete 13-tooth/19-tooth OSPW System
- CeramicSpeed Bearing Oil in 15ml dropper bottle
$529.00 - $629.00
Entirely developed, designed, and produced in Denmark by CeramicSpeed, the Oversized Pulley Wheel System for SRAM eTap is a technological advance for the cycling industry.
Matching the highest quality materials with a unique design, the OSPW System delivers lower friction and longer lifetime, improving your competitive advantage. Thanks to the OSPW System for SRAM eTap, the power savings start at 40%, and the CeramicSpeed Bearings inside offers a 3-5 times longer lifespan compared to standard pulleys on the market. The watt savings with a CeramicSpeed OSPW System for SRAM eTap start at 1.6 watts.
This 17/17-tooth OSPW system for SRAM eTap derailleurs is compatible with up to a 32 tooth cassette and with both short cage & WiFli derailleur bodies. The product is for 11-speed eTap and is not compatible with 12-speed SRAM eTap AXS.
If you have the updated 11-speed SRAM eTap derailleur featuring the orbit clutch, you will need the CeramicSpeed OSPW System for SRAM eTap AXS derailleurs.
The typical overall power savings of the OSPW System for OSPW System for SRAM eTap is 40%-60% over a stock setup.
The oversized pulley wheels have lifespan that is 3-5 times longer than the commonly used standard pulleys on the market.
In The Box:
- Oversized Pulley Wheel System
- CeramicSpeed Bearing Oil in 15ml dropper bottle
- Sticker Sheet
$529.00
Developed and designed entirely by CeramicSpeed, the Oversized Pulley Wheel (OSPW) System for Shimano 9000/6800 provides the ultimate optimization of your bicycle's drivetrain.
This OSPW System features a set of 17-tooth aluminum Pulley Wheels housed in a specially designed polyamide (PA) and carbon cage.
The upper and lower 17-tooth oversized aluminum pulley wheels come fitted with either standard or coated CeramicSpeed Bearings.
The Oversized Pulley Wheel (OSPW) System is the product of choice by many of the world's leading cycling teams and triathletes.
This specific system is compatible with Ultegra 6700/6770/6800/6870 mechanical and Di2 rear derailleurs and Dura Ace 7900/7970/9000/9070 mechanical and Di2 rear derailleurs. It is not compatible with Shimano Dura-Ace 9100/9150 and Ultegra 8000 series rear derailleurs. For those rear derailleurs you will need a OSPW System for Shimano 9100 series.
The system is compatible with up to a 28-tooth cassette on most bikes, depending on derailleur hanger.
The typical overall power savings of the OSPW System for Shimano 9000/6800 is 30%-60% over a stock setup, and the oversized pulley wheels have a lifespan that is 3-5 times longer than the commonly used standard pulleys on the market.
In The Box:
- A complete 17-tooth OSPW System
- CeramicSpeed bearing oil in 15ml dropper bottle
$579.00
Improve the performance of your 11-speed Shimano rear derailleur with pulleys that reduce friction and increase bearing life. Ours are designed to work with less drag, adding to the power transmitted to the rear wheel.
Our Titanium Pulley Wheels for Shimano 11s are available with CeramicSpeed Coated Bearings that add an extra layer to the performance of the product. The Coated Bearings have races 75% harder than our hardened-steel races. They last 60% longer than our Standard Bearings. Bearing drag is decreased by over 50% compared to our Standard Bearings. Both our Standard and Coated come with the same super-hard, super-round CeramicSpeed Balls.
Designed in light and strong machined Titanium, these Pulley Wheels offer three times the lifespan of our alloy Pulley Wheels, and are compatible with all 11-speed Shimano derailleurs.
- There is both an upper and lower-specific pulley in the set. They are marked accordingly and have directional arrows, as well.
- These pulleys are compatible with all Shimano 11-speed rear derailleurs, both mechanical and electronic.
- The kits come with CeramicSpeed oil in a 15ml dropper bottle, and the bearings come pre-oiled.
In the box:
- 2 x 11-tooth pulley wheels
- 4 x spacers
- CeramicSpeed Bearing Oil in 15 ml dropper bottle
- Sticker sheet
$589.00 - $689.00
The Oversized Pulley Wheel System for SRAM Red and Force AXS features a 15-tooth upper and 19-tooth lower pulley wheel setting for maximum efficiency. The handbuilt OSPW System has two spring tension settings that offer you customized setup based on riding conditions.
This OSPW System is also compatible with the 2020 11-speed SRAM Red eTap derailleurs featuring a clutch.
- Pulley wheels: CeramicSpeed 15-tooth upper and 19-tooth lower
- Pulley wheel material: aluminum
- Cage material: carbon-reinforced PA
- Bearing options: CeramicSpeed Standard or Coated
- Compatibility: SRAM Red AXS and SRAM Force AXS. 2020 SRAM Red eTap 11-speed derailleur with the orbit clutch. This system is also compatible with the wider-range Force AXS medium cage derailleur
- Cassette Compatibility: Fits 12-speed 10-36 tooth cassettes. Fits 11-32 tooth cassettes when used with an 11-speed clutched derailleur
- Spring Tension Settings: 2-spring
- Speeds: 12-speed
- Discipline: Road and Gravel/Cross
- Custom tool included for removal of stock cage and securing of OSPW. The factory clutch mechanism will remain intact. There is no damage or modification to the clutch for the installation of the OSPW System
In the box:
- Complete OSPW System for SRAM Red/Force AXS
- CeramicSpeed Pulley Oil, 15 ml dropper bottle
- Custom tool for removal of stock cage and securing of OSPW System
$589.00 - $689.00
The OSPW X for SRAM Eagle AXS features a narrow wide tooth profile to ensure durable chain retention.
The 14-tooth upper and 18-tooth lower pulleys reduce chain drag, while the custom-designed carbon fiber pulley cage ensures both durability and light weight.
- Pulley Wheels: CeramicSpeed 14-tooth upper and 18-tooth lower
- Pulley Wheel Material: aluminum
- Cage Material: Carbon-reinforced PA
- Bearing Options: CeramicSpeed Standard or Coated
- CeramicSpeed Grease/Oil: Pulley Oil
- Compatibility: SRAM Eagle AXS (Electronic)
- Compatibility Cassette: 10-52 tooth max
- Spring Tension Settings: 3
- Speed: 12-speed
- Discipline: Off-road and Gravity
In the box:
- A complete OSPW X System for SRAM Eagle AXS
- CeramicSpeed Bearing Oil in a 15ml dropper bottle
$689.00
The fastest oversized pulley wheel system in the world is also available for SRAM Rival & Force 1 Type 3 derailleurs.
Featuring 14-tooth (upper) and 18-tooth (lower) pulleys with a narrow-wide profile, the OSPW X System for SRAM Rival & Force 1 Type 3 is available fitted with CeramicSpeed standard or coated bearings, with up to a 6-year warranty. The unique narrow-wide tooth profile of the pulleys ensures durable chain retention.
The system is fitted with a custom-designed, strong carbon fiber pulley cage assembly for outstanding durability and light weight. The cage design allows you to choose between two spring tension settings to customize performance and reduce chain drag. We recommend initial setup in the lower spring tension. This has been designed to leave the clutch mechanism fully functional for chain retention.
In the event that the low spring tension does not provide adequate shift quality on very rough roads, you can increase it to the high-spring tension, which corresponds to the factory settings.
Thanks to the high-quality CeramicSpeed Bearings inside, your product will benefit from a 3-5 times longer lifespan than stock, and it has been tested to deliver 30-40% less friction than conventional systems.
This product is completely developed and handbuilt in Denmark, including the top quality CeramicSpeed Bearings inside.
The OSPW X System for SRAM Rival & Force 1 Type 3 is compatible with SRAM Rival or Force 1X 11-speed with Type 3 clutch, regardless of the cage length. Note that the cage lock must be in the 8 o'clock position, not the 5 o'clock position. This product is NOT compatible with Type 2.1 clutch derailleurs.
In The Box:
- A complete 14-tooth/18-tooth OSPW X System for SRAM 1x
- CeramicSpeed bearing oil in 15ml dropper bottle
- Sticker Sheet